- #Microwire eeprom programmer serial#
- #Microwire eeprom programmer update#
- #Microwire eeprom programmer software#
- #Microwire eeprom programmer Pc#
- #Microwire eeprom programmer series#
> for programming 24Cxx series EEPROM device. > I am going to use the circuit shown in below link
#Microwire eeprom programmer software#
Chery QQ 93C66 - software for direct eeprom programming.
#Microwire eeprom programmer serial#
There is no standard data flow, so in this case is the meaning of pin descriptions more or less irrelevant. The Microchip 93C46C device is a 1Kb Microwire (3-wire) Serial EEPROM with hardware selectable.
#Microwire eeprom programmer Pc#
inverted/not inverted signals) internally.Ĭommunication ports COM and LPT are used by the PonyProg2000 ONLY as a PC input / output interfaces with direct access to their pins. So if you choose in PonyProg2000 on the interface setup dialog the correct interface type, the software automatically makes needed settings (e.g. Reading the input "data" (voltage levels at LPT pins 12 and 13) at the time defined by the communication protocol is controlled by software as well. The output data is "created" by generating voltage levels (log.0 = 0V and log.1 = 5V) for driving external transistors (pin 2, pin 3). The transistors are in this direction unused.Įvery communication is fully controlled by software - PonyProg2000. For receiving data (from i2c device to PC) are only used LPT pin 12 and pin 13. The two transistors connected to LPT connector on pin 2 and pin 3 are used only by the "data" transmission from pc to the i2c device connected via easyI2Cbus interface. We don't take any responsibility to use this function.1. Multi-COM don't answer to any questions related with operation on IMEI number - if you require help in this metter please contact with software/device producer directly. It's prohibitted to use this function to change IMEI to diffrent that original. Multi-voltage I/O devices 3.3v and 5v memory devices. Ultra High Density (1Gb+ SPI devices) 16, 24, and 32-bit addressing.
SPI Flash Memory SPI mode 0, 1 and 2 supported. 8 MHz SPI clock speed Up to 350KB/s read and 200KB/s write. I2C, SPI and Microwire memory interfaces are supported. NOTE: The FlashcatUSB programmer is sold separately and not included with any of the adapters.
We want to inform that IMEI change option in softwares are intended to use only to repair broken IMEI and retrieve it to original state. EEPROM memory programming was never easier CodiProg USBMK2 is an universal EEPROM tool that allows to read, edit and write various types of EEPROM memories. We don't guarantee that software/device will work or any other system - especially 64-bit systems, iMac, Linux. Information concerning hardware requiments:įor proper working with this device producer suggest PC computer with 32-bit Windows XP operating system. At the moment it supports I☬ Bus, Microwire, SPI eeprom, the Atmel AVR and Microchip PIC micro. The EEISP-U programmer also supports AT17LVxxx and AT17Fxxx FPGA configurator EEPROMs. Device supported including all 24 Series (I2C), 25 series (SPI) and 93 series (Microwire) serial EEPROMs. Its purpose is reading and writing every serial device. Kanda serial EEPROM programmers use ISP programming to copy, read and program serial EEPROM devices. PonyProg is a serial device programmer software with a user friendly GUI framework available for Windows95, 98, 2000 & NT and Intel Linux. Leaving it enabled can occurs inproper operation of software / services and you will get communications errors like “Error 10060”. Introduction : If you are looking for a simple but powerful programmer you are right, its here. Information concerning the interoperability of digital content:įor using a software or a piece of software that the manufacturer supplies with purchased hardware, in some cases it’s required that you disable your Firewall ( in software or router) and antivirus software.
#Microwire eeprom programmer update#
Before you attempt to make software update on the device or want to activate/use service, make sure that you have a sufficient link parameters. EEPROM memory programming was never easier CodiProg USBMK2 is an universal EEPROM tool that allows to read, edit and write various types of EEPROM memories. capacity of 1024 kb / s ( download) and 512 kb / s ( upload). With a team of extremely dedicated and quality lecturers, microwire eeprom programmer will not only be a place to share knowledge but also to help students get inspired to explore and discover many creative. The correct use of the purchased goods is required to have a stable internet connection with min. microwire eeprom programmer provides a comprehensive and comprehensive pathway for students to see progress after the end of each module. Additional information about this product: Information concerning technical requiments :
0 kommentar(er)
